Free UK delivery on orders over £150
Valvenok
JOSCAR RegisteredBVAA member
Track Order
Quick Order
Cart
Sign In
Request a quote

Hydraulic actuators

Susin I-Tork

LP-HD / LP-HS Series Low-pressure Scotch Yoke

Self-contained electro-hydraulic actuators for quarter-turn valves and dampers: a scotch yoke actuator with its own motor, pump and valve block at 8 bar, so it needs only electric power. Double acting up to 4,635 Nm, or spring return to fail close or fail open. 30 models.

Models
30 (sizes 45 – 200)
Torque
Up to 4,635 Nm
On-board pressure
Max. 8 bar
Power
180 – 250 W, 400 V / 230 V
Fail-safe
Spring return, NC or NO
Hazardous areas
Zone 1 and 2
How a low-pressure scotch yoke works
SHUTOPENPort APort BHydraulic cylinderYoke turns the valve 90°Oil, 8 bar, own pumpValve shutOil in at port A: the pin turns the yokeTurned 90°: valve openOil in at port B: the piston drives backValve shut
Oil under pressure Roller pin in the yoke slot Valve position
LP-HS spring return low-pressure electro-hydraulic actuator with red scotch yoke body

How It’s Built

  • Scotch yoke. A hardened scotch yoke gives more torque at the open and close positions, closely matching what a valve needs.
  • Own hydraulic power. Electric motor (180 – 250 W) and pump at up to 8 bar, with a solenoid valve at 24 V DC or 230 V; speed adjustable by throttle.
  • Spring pack. Pre-compressed for safety on the spring return LP-HS, to close or open the valve when power is lost.
  • Cylinder. Extruded, anodised aluminium with a polished finish and specially treated O-rings for low friction and long life.
  • Stops and indicator. Centre stopper bolts adjust the open and close positions; flat or dome position indicator.
  • Mounting. ISO 5211, DIN 3337 and NAMUR drive; accessories mount to VDI/VDE 3845 NAMUR.

Why this range

No Compressor, No Tubing

The LP range puts a scotch yoke actuator, a small electric pump and a valve block in one unit. It does what a pneumatic scotch yoke does, without an air supply: a good fit where a compressor and air lines would serve only a few valves.

Pneumatic scotch yoke (PDS)
LP-HD / LP-HS
Power source
Compressed air from the plant
Electric power only: own motor and pump
Pipework
Air lines and tubing to every actuator
None: a self-contained unit on the valve
Fail-safe
Spring return, needs air to stroke
Spring return LP-HS, normally closed or open
Speed
Set by air supply and restrictors
Adjustable by throttle; set by the HPU chosen
Good for
Plants with an air supply and many valves
Remote or few valves, no compressor on site
Same yoke as the PDS range
Sizes 45 to 200 match Susin I-Tork’s PDS pneumatic scotch yoke, with its hardened yoke, centre stopper bolts and NAMUR mounting.
See the PDS range
Hydraulic power unit (HPU) sizing
The catalogue lists stroking times for each size by HPU, from 3.6 s on the smallest to about 68 s on the largest. Every model page shows the times for its size.

FAQ

LP-HD / LP-HS Questions

What does it need to run?

Electric power only: 400 V 50/60 Hz or 230 V 50 Hz for the motor, and 24 V DC or 230 V for the solenoid valve. The pump makes its own hydraulic pressure, up to 8 bar, so no compressed air or hydraulic supply is needed.

Double acting or spring return?

LP-HD is double acting: the pump drives the valve both ways. LP-HS is spring return: normally closed models fail closed and normally open models fail open when the power goes.

How do I choose the size?

Compare the valve’s torque with the actuator torque at the start, middle and end of the stroke on the model page, with a safety margin, then check the ISO 5211 flange.

How fast does it stroke?

It depends on the hydraulic power unit. The catalogue gives stroking times for each size and HPU, from 3.6 s on the smallest; speed is also adjustable by throttle.

Can it go in a hazardous area?

The catalogue lists it for Zone 1 and 2. Tell us the zone and gas group and we’ll confirm the build.

LP-HD or PANDA?

Both are low-pressure electro-hydraulic units at 8 bar. LP-HD / LP-HS uses a scotch yoke actuator with torque shown across the stroke; PANDA is a different compact design with its own sizes. Send us the valve and we’ll suggest one.

No Air Supply on Site?

Compare all 30 LP models, or send us the valve torque, flange, supply voltage and the fail position you need and we’ll pick the size.